ShelterLogic 72853.0 Manuel d'instructions télécharger pdf

ShelterLogic, LLC

150 Callender Road

Watertown, CT 06795

www.shelterlogic.com

1-800-524-9970

1-800-559-6175

Canada:

Page 8

Assembly Instructions

10' W x 8' H or 10' H

Peak Style

Frame Assembly

Before you start: 2+ individuals recommended for assembly, approximate time 3 hours.

Recommended tools: Power Drill, Safety Glasses, Rope, Tape Measure, Ratchet with Socket Set,

Adjustable Wrench, Step Ladder, Rubber Mallet, Utility Knife, 5/8 Concrete Drill Bit, Sledge Hammer.

05-10ET13-0A

10. SECURING YOUR COVER:

A. Install the “S”- hook from the ratchet assembly into the legs of

the shelter. Pull the webbing carefully to remove the slack from the

cover. Do not to pull the webbing through the opposite side of the

cover.

B. Insert the webbing through the spindle of the ratchet and pull

tight. See Detail O. Wind the ratchet until the webbing overlaps

itself. Repeat these steps on the opposite side, then repeat this

on the back side of the shelter.

C. When all of the corners are secured, adjust the cover front to

back so that it is centered. When the cover is centered, tighten all

of the ratchets. Do this in an “X” pattern to be sure it is tightened

evenly. See Detail O.

D. Install the cover rails (10110) by inserting them into the pipe

pockets on each side of the cover. Bolt (10115) the rails to the ribs

using the 3-way and 4-way clamps as shown in Detail P. Check

that the rails are evenly spaced 8” above the ground on both

sides. Push down on the cover rails and connectors, one at a

time, to tighten the bolted clamps and the cover.

IMPORTANT: Install bolt caps (10150) on exposed bolts on side

rails and wind braces to prevent injury.

DETAIL O

OUTSIDE

CORNER

VIEW

10115

01010

11102

10115

10111

01010

DETAIL P

NOTE: CHECK THAT

YOUR COVER IS

CORRECTLY PLACED

ON THE FRAME.

The ShelterLogic

logo should line

up on the left front and right rear

corners near the top rail. If the logo

is not legible and positioned as

shown as “incorrect”, the cover has

not been put on the frame correctly.

CORRECT

INCORRECT

Check and

tighten Ratchets

and Cross Rails

monthly to ensure

the cover is tight.

Cover Tightening Tip

clamps

CORNER LEG

MIDDLE LEG

WARNING: Serious injury to persons or property could result if cover is installed and shelter is not

completed and is left unattended. Shelter must be securely anchored until completed.

10110

1 2 3 4

Résumé du contenu

Page 1 - Assembly Instructions

ShelterLogic, LLC150 Callender RoadWatertown, CT 06795www.shelterlogic.com1-800-524-99701-800-559-6175Canada:Page 8Assembly Instructions10' W x 8

Page 2 - 10' W X 10' H

Page 3Page 205-10ET13-0A05-10ET13-0A10'W x 10'H Peak Style Frame AssemblyPlease read and understand instructions completely before assembly.

Page 3 - 8' HIGH

Page 5Page 5Page 405-10ET13-0A05-10ET13-0AASSEMBLY OF PEAK STYLE GARAGE SHELTERNOTE FOR FRAME EXTENSION KIT: 10’ x 8’ is the base frame dimension. Yo

Page 4 - 7. INSTALL AUGER ANCHORS:

Page 6Page 705-10ET13-0A05-10ET13-0A6. SECURE BASE FEET:A. Slide leg pipe over over the base feet, line up the holes in the pipe with the holes in the

Commentaires sur ces manuels

Pas de commentaire

ShelterLogic 72853.0 Manuel d'instructions

Naviguer en ligne ou télécharger Manuel d'instructions pour Non ShelterLogic 72853.0. ShelterLogic 72853.0 Instructions / Assembly Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Non ShelterLogic 72853.0